Spectra-precision Survey Pro v4.5 Ranger Reference Manual User Manual Page 222
- Page / 475
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Survey Pro Reference Manual
R-214
Localization Calculator
This sub section describes a feature available only in Ground – TDS
Localization mode.
The Localization Calculator is used to enter the
horizontal localization parameters using the
pre-Survey Pro 3.5 procedure.
Scale: is where you enter the scale factor used
to transform distances on the localization
mapping plane to your project coordinate
system.
Note: Using versions of Survey Pro after 3.5,
the localization scale should be very close to
1.0. See the user's manual for a more detailed explanation of
localization scale values.
Rotation: is where you enter the rotation angle used to transform the
orientation of the localization mapping plane to your grid orientation
of your project.
Calc. Scale : opens the Localization Calculator screen where the
horizontal scale factor is explained.
Calc. Rotation : opens the Localization Calculator screen where the
rotation can set parallel to a mapping plane selected from the
database.
Base Station Local Coordinate: are the local plane coordinates of the
base. If you set up on a new base point, these fields are blank and
you need to occupy one control point to calculate the base station local
coordinates.
Occupy Control : opens the Control Points screen (Page R-190), where
you select a control point to occupy. When you are done, the base
local coordinate is calculated using your entered scale and rotation.
Solve > : computes the horizontal localization parameters using the
entered scale, rotation, and base station local coordinates.
- SURVEY PRO 1
- Table of Contents 3
- Welcome 9
- Main Menu 11
- GPS Status 13
- File Menu 15
- Open / New 16
- New Job 16
- External Control File) 17
- Create a New Job 3 18
- Control File) 19
- Save As 22
- Import *.JOB Coordinates 24
- Import *.CR5 Coordinates 25
- Import *.GPS Coordinates 25
- Import *.TXT Coordinates 26
- Import LandXML Coordinates 28
- Confirm Point Replace 29
- Export – Screen Two 31
- Export *.JOB Coordinates 31
- Export Old *.JOB Coordinates 31
- Export *.CR5 Coordinates 32
- Export *.TXT Coordinates 32
- Export *.CSV Coordinates 33
- Import Control Points 34
- Backup / Restore Job 35
- Backup / Restore – Backup 37
- Backup/Restore – Restore 38
- Transfer 39
- Register Modules 40
- About Survey Pro 41
- Job Menu 43
- NOTICE: 48
- Units Settings 49
- Format Settings 51
- Files Settings 52
- Surveying Settings 53
- Stakeout Settings 55
- Level Settings 58
- FGCS Defaults 60
- Repetition Settings 61
- Date/Time Settings 62
- Buttons Settings 63
- Edit Points 66
- Edit Point – General 68
- Point Feature Attributes 69
- Edit Point – Location 69
- Edit Point – Geodetic 70
- Edit GPS Point Flags Screen 71
- Edit Polylines 72
- Screen Four – Add/Edit Curve 74
- Adding a Spiral 75
- Adding a Vertical Curve 75
- Edit Alignment 77
- Edit Segment – Spiral Card 81
- Auto Linework 83
- View Raw Data File 87
- View DTM 88
- Layers for Staking DTM 89
- Choose Polyline 90
- Add/Edit Break-lines 90
- Edit Polyline 91
- Points on DTM Layer 92
- 3D View 93
- 3D View Settings 93
- Manage Layers 95
- Job Information 96
- Calculator 98
- Job Menu – GPS 101
- Settings 102
- Receiver Setup 103
- Rx Settings 105
- Data Modem Settings 106
- Modem Serial Comms Screen 108
- Radio Settings Screen 108
- Cell Phone Settings Screen 110
- General Settings 111
- Measure Mode Settings 114
- Post Process Settings 115
- Job Menu – Basic GPS 117
- Change Settings 119
- Bluetooth Setup Wizard 120
- Radio Settings 121
- Change Radio Settings Screen 122
- Stakeout 124
- Date/Time 124
- Buttons 124
- General 124
- Survey Menu 125
- Backsight Setup 126
- Backsight Solved 128
- Check Backsight 130
- Check by Distance Results 130
- Check by Angle Results 131
- Backsight Circle 131
- Traverse / Sideshot 132
- Results 133
- Traverse Now or Later? 134
- New Occupy Point 135
- Point Exists 136
- Remote Shot (Remote Mode) 137
- Repetition Shots 138
- Multiple Sideshots 140
- Radial Sideshots 141
- 1_ft back 142
- 3_ft right 142
- Horizontal Angle Offset 143
- Vertical Angle Offset 144
- Auto Collect 145
- Auto Collect – Screen Two 146
- Corner & 2 Lines 147
- Corner & Angle 148
- Corner & Offset 149
- Corner & Plane 150
- Surface Scan 151
- Angle Grid 152
- Surface Scan Statistics 153
- Surface Scan Results 154
- Video Scan 155
- Video Scan Settings 158
- Shoot From Two Ends 159
- Record Mode 160
- Resection 161
- Save Point 162
- Remote Elevation 163
- Check Point 164
- Solar Observation 165
- Sun Shot Procedure Summary 168
- Remote Control 170
- Turn To 171
- Results Card 172
- Video Card 173
- Video Display Options 174
- Map Card 175
- Aim Card 176
- Foresight Card 176
- Sky Plot 177
- GeoLock Settings 178
- Survey Menu – GPS 179
- Cell Modem 181
- Post Process 182
- Sky View 183
- Sat Info 184
- Position 185
- Start GPS Survey 186
- Choose Projection Mode 187
- Choose Base Setup 187
- Select Geoid Model 188
- Connect To Receiver 189
- Base Setup 190
- Receiver Antenna 192
- Vertical Offset 193
- Base Setup Two – SET 194
- Base Setup Two – GET and SET 194
- Rover Setup 196
- Solve Localization 197
- Data Collection 198
- Feature Collection Screen 199
- Offset Shots 201
- Occupy Data Points Screen 202
- Control Points 203
- Check Control Point Screen 204
- Occupy Control Point Screen 205
- Post Processing 207
- Projection 213
- Projection Details 215
- Localization Set Zone 215
- Select Coordinate System 217
- Select Database 217
- Horizontal Card 221
- Vertical Card 221
- Localization Calculator 222
- Solve Localization – Results 224
- Key in Zone 229
- Key In Zone - Ellipse 231
- Key In Zone - Results 233
- Ground Coordinates 234
- Ground Coordinates - Scale 235
- Ground Coordinates - Results 236
- Import GPS Control 239
- Review Results and Finish 241
- Multiple Point Results 242
- Receiver Information 243
- Adjust with Projection 244
- Coordinate System 247
- Projection Calculator 249
- Height Correction 250
- File Management 251
- Recoverable Files 252
- Survey Menu – Basic 253
- Start Survey – More than One 256
- Matching Base Point 256
- Start Survey – No 256
- GPS Backsight/Resection 257
- Occupy Control Setup 258
- Occupy Control Point 258
- Resection for New Base Point 258
- Leveling Menu 265
- Select/Create Loop 266
- New Level Loop – Screen Two 267
- Level Notes 267
- Level Notes Settings 268
- Leveling Shots 270
- Leveling Shot Results 271
- Leveling Side Shot 272
- Leveling Stakeout 273
- Turn to Benchmark 274
- Close Loop 275
- 2 Peg Test 276
- Adjustment 277
- Adjustment – Preview Screen 278
- Leveling Remote Control 279
- Stakeout Menu 281
- Stake Points 282
- Stake Points – Screen Two 283
- Stake Points – Screen Three 284
- ) dialog box 285
- Instrument Stakeout 286
- Remote Staking 287
- Stake List of Points Screen 288
- Edit Point List 289
- Stake to Line 290
- Stake to Line – Screen Two 291
- Remote Stake to Line 293
- Offset Staking – Screen Two 295
- Offset Staking – Screen Four 297
- Offset Staking – Screen Five 298
- Offset Staking – Screen Six 300
- Slope Staking 301
- Slope Staking – Screen Three 302
- Slope Staking – Screen Four 303
- Slope Staking – Screen Five 305
- Slope Staking Offset Stake 306
- Point Slope Staking 307
- value increases 312
- screen, described 312
- screen, which is 313
- Screen Summary 317
- Stake Spiral and Offset 318
- Summary 321
- Show Station 322
- Stake DTM 327
- Choose a Centerline 329
- Stake DTM – Screen Two 330
- Station Staking 332
- Cross-Section View 333
- you want to stake 334
- information is 334
- Define a Location 336
- Where is Next Point 338
- Stakeout Menu – GPS 341
- Show Station and Offset 351
- Store Offset Points 352
- routine for GPS are 352
- Inverse Menu 357
- Inverse Point to Point 358
- Inverse Point to Multiple 362
- Inverse Point to Location / 363
- Cogo Menu 365
- Point in Direction 366
- Intersection 367
- Corner Angle 372
- Compute Area 373
- Triangle Solutions 374
- Map Check 375
- Add / Edit Line 376
- Add / Edit Curve 376
- Add to Map 377
- Predetermined Area 378
- HD/VD to SD/ZA 380
- SD/ZA to HD/VD 381
- AU Conversion 382
- Curve Menu 383
- Curve Solution 384
- Results: 385
- Known PI and Tangents 386
- Three Point Curve 387
- Compute Radius Point 389
- Line Tangent to Circle 391
- Curve Layout 392
- Tan Dist 393
- Chord Dist 394
- Traverse on Curve 396
- Parabolic Curve 398
- Parabolic Layout 400
- Straight Grade 402
- Spiral Layout 404
- Traverse on Spiral 405
- Roads Menu 407
- Add/Edit Templates 408
- and the slope 409
- Edit Segment 410
- Edit Alignments 411
- Add/Edit Roads 411
- Roadname 412
- The Road Card 413
- Roads Report Screen 413
- Road Profiles Screen 415
- The Templates Card 416
- Add / Edit Template Screen 417
- The Widenings Card 418
- Add / Edit Widening Screen 419
- Super Elevations Card 420
- Road Stakeout 423
- if any 425
- Stake Road – Screen Four 426
- Road Slope Staking 429
- H. Map Card 430
- V. Map Card 430
- Slopes Card 431
- Cut/Fill Hinge Points Cards 431
- Road Station and Offset 432
- screen where 432
- Alignment Card 433
- Cross-Section Card 434
- Shot Data Card 434
- Station Equation 435
- Adjust Menu 437
- Translate 439
- Traverse Adjust 442
- Traverse Adjust – Results 446
- Miscelaneous Screens 447
- Past Results 448
- Create Points Screen 448
- Trimble Slant HR -> HR 449
- Convert Slant HI to HI 449
- Quick Pick Editor 450
- Point List Editor 451
- Map View 452
- Map Display Options 454
- Manage Basemaps 455
- Edit Basemaps 456
- Smart Targets 457
- : when checked, the offset 458
- Disable Touch-Screen 461
- Appendix A 463
- Lambert Zones 464
- ...........151, R-386 467
- .................. 151 468
- ............... 151 468
- .............. R-49 468
- ......121, R-134 468
- .R-306 473
- ....R-303 473
- ........ R-314 474
- 16, R-344 474
- ...... 151, R-385 474
Related products and manuals for Software Spectra-precision Survey Pro v4.5 Ranger Reference Manual
(339 pages)© 2020, manymanuals.com. All rights reserved. | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals