Spectra-precision Survey Pro v4.5 Ranger Reference Manual User Manual Page 108
- Page / 475
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Survey Pro Reference Manual
R-100
Edit : Opens the Cell Phone Settings or IP Modem Settings screen
(Page R-102 or R-103, respectively) where the selected data modem
configuration can be modified.
Delete : Deletes the selected data modem configuration.
Modem Serial Comms Screen
The Modem Serial Comms. screen is used to change the settings for
communication between the base or rover receiver and the data
modem.
GPS Receiver Port: is where you select the
serial port the receiver will use to communicate
with the modem.
Baudrate: is where you select the baud rate the
receiver will use to communicate with the
modem.
Parity: is where you select the parity the
receiver will use to communicate with the
modem. This setting disabled for receivers that
do not support user defined parity setting.
Defaults : automatically sets all the selectable values to their
defaults based on the current receiver hardware.
Receiver Set : sets the selected modem communication settings for
the specified port on the receiver.
Note: The modem communication settings are also set in the receiver
during the base and rover setup procedure. Therefore, you will not
usually have to use the Receiver Set button on this page.
Radio Settings Screen
The Radio Settings screen is used to configure settings of the base or
rover radio modem. All settings available are described below.
However, not all radios support all of the described settings, so if you
do not see one of these fields, it is because the radio type does not
support it.
- SURVEY PRO 1
- Table of Contents 3
- Welcome 9
- Main Menu 11
- GPS Status 13
- File Menu 15
- Open / New 16
- New Job 16
- External Control File) 17
- Create a New Job 3 18
- Control File) 19
- Save As 22
- Import *.JOB Coordinates 24
- Import *.CR5 Coordinates 25
- Import *.GPS Coordinates 25
- Import *.TXT Coordinates 26
- Import LandXML Coordinates 28
- Confirm Point Replace 29
- Export – Screen Two 31
- Export *.JOB Coordinates 31
- Export Old *.JOB Coordinates 31
- Export *.CR5 Coordinates 32
- Export *.TXT Coordinates 32
- Export *.CSV Coordinates 33
- Import Control Points 34
- Backup / Restore Job 35
- Backup / Restore – Backup 37
- Backup/Restore – Restore 38
- Transfer 39
- Register Modules 40
- About Survey Pro 41
- Job Menu 43
- NOTICE: 48
- Units Settings 49
- Format Settings 51
- Files Settings 52
- Surveying Settings 53
- Stakeout Settings 55
- Level Settings 58
- FGCS Defaults 60
- Repetition Settings 61
- Date/Time Settings 62
- Buttons Settings 63
- Edit Points 66
- Edit Point – General 68
- Point Feature Attributes 69
- Edit Point – Location 69
- Edit Point – Geodetic 70
- Edit GPS Point Flags Screen 71
- Edit Polylines 72
- Screen Four – Add/Edit Curve 74
- Adding a Spiral 75
- Adding a Vertical Curve 75
- Edit Alignment 77
- Edit Segment – Spiral Card 81
- Auto Linework 83
- View Raw Data File 87
- View DTM 88
- Layers for Staking DTM 89
- Choose Polyline 90
- Add/Edit Break-lines 90
- Edit Polyline 91
- Points on DTM Layer 92
- 3D View 93
- 3D View Settings 93
- Manage Layers 95
- Job Information 96
- Calculator 98
- Job Menu – GPS 101
- Settings 102
- Receiver Setup 103
- Rx Settings 105
- Data Modem Settings 106
- Modem Serial Comms Screen 108
- Radio Settings Screen 108
- Cell Phone Settings Screen 110
- General Settings 111
- Measure Mode Settings 114
- Post Process Settings 115
- Job Menu – Basic GPS 117
- Change Settings 119
- Bluetooth Setup Wizard 120
- Radio Settings 121
- Change Radio Settings Screen 122
- Stakeout 124
- Date/Time 124
- Buttons 124
- General 124
- Survey Menu 125
- Backsight Setup 126
- Backsight Solved 128
- Check Backsight 130
- Check by Distance Results 130
- Check by Angle Results 131
- Backsight Circle 131
- Traverse / Sideshot 132
- Results 133
- Traverse Now or Later? 134
- New Occupy Point 135
- Point Exists 136
- Remote Shot (Remote Mode) 137
- Repetition Shots 138
- Multiple Sideshots 140
- Radial Sideshots 141
- 1_ft back 142
- 3_ft right 142
- Horizontal Angle Offset 143
- Vertical Angle Offset 144
- Auto Collect 145
- Auto Collect – Screen Two 146
- Corner & 2 Lines 147
- Corner & Angle 148
- Corner & Offset 149
- Corner & Plane 150
- Surface Scan 151
- Angle Grid 152
- Surface Scan Statistics 153
- Surface Scan Results 154
- Video Scan 155
- Video Scan Settings 158
- Shoot From Two Ends 159
- Record Mode 160
- Resection 161
- Save Point 162
- Remote Elevation 163
- Check Point 164
- Solar Observation 165
- Sun Shot Procedure Summary 168
- Remote Control 170
- Turn To 171
- Results Card 172
- Video Card 173
- Video Display Options 174
- Map Card 175
- Aim Card 176
- Foresight Card 176
- Sky Plot 177
- GeoLock Settings 178
- Survey Menu – GPS 179
- Cell Modem 181
- Post Process 182
- Sky View 183
- Sat Info 184
- Position 185
- Start GPS Survey 186
- Choose Projection Mode 187
- Choose Base Setup 187
- Select Geoid Model 188
- Connect To Receiver 189
- Base Setup 190
- Receiver Antenna 192
- Vertical Offset 193
- Base Setup Two – SET 194
- Base Setup Two – GET and SET 194
- Rover Setup 196
- Solve Localization 197
- Data Collection 198
- Feature Collection Screen 199
- Offset Shots 201
- Occupy Data Points Screen 202
- Control Points 203
- Check Control Point Screen 204
- Occupy Control Point Screen 205
- Post Processing 207
- Projection 213
- Projection Details 215
- Localization Set Zone 215
- Select Coordinate System 217
- Select Database 217
- Horizontal Card 221
- Vertical Card 221
- Localization Calculator 222
- Solve Localization – Results 224
- Key in Zone 229
- Key In Zone - Ellipse 231
- Key In Zone - Results 233
- Ground Coordinates 234
- Ground Coordinates - Scale 235
- Ground Coordinates - Results 236
- Import GPS Control 239
- Review Results and Finish 241
- Multiple Point Results 242
- Receiver Information 243
- Adjust with Projection 244
- Coordinate System 247
- Projection Calculator 249
- Height Correction 250
- File Management 251
- Recoverable Files 252
- Survey Menu – Basic 253
- Start Survey – More than One 256
- Matching Base Point 256
- Start Survey – No 256
- GPS Backsight/Resection 257
- Occupy Control Setup 258
- Occupy Control Point 258
- Resection for New Base Point 258
- Leveling Menu 265
- Select/Create Loop 266
- New Level Loop – Screen Two 267
- Level Notes 267
- Level Notes Settings 268
- Leveling Shots 270
- Leveling Shot Results 271
- Leveling Side Shot 272
- Leveling Stakeout 273
- Turn to Benchmark 274
- Close Loop 275
- 2 Peg Test 276
- Adjustment 277
- Adjustment – Preview Screen 278
- Leveling Remote Control 279
- Stakeout Menu 281
- Stake Points 282
- Stake Points – Screen Two 283
- Stake Points – Screen Three 284
- ) dialog box 285
- Instrument Stakeout 286
- Remote Staking 287
- Stake List of Points Screen 288
- Edit Point List 289
- Stake to Line 290
- Stake to Line – Screen Two 291
- Remote Stake to Line 293
- Offset Staking – Screen Two 295
- Offset Staking – Screen Four 297
- Offset Staking – Screen Five 298
- Offset Staking – Screen Six 300
- Slope Staking 301
- Slope Staking – Screen Three 302
- Slope Staking – Screen Four 303
- Slope Staking – Screen Five 305
- Slope Staking Offset Stake 306
- Point Slope Staking 307
- value increases 312
- screen, described 312
- screen, which is 313
- Screen Summary 317
- Stake Spiral and Offset 318
- Summary 321
- Show Station 322
- Stake DTM 327
- Choose a Centerline 329
- Stake DTM – Screen Two 330
- Station Staking 332
- Cross-Section View 333
- you want to stake 334
- information is 334
- Define a Location 336
- Where is Next Point 338
- Stakeout Menu – GPS 341
- Show Station and Offset 351
- Store Offset Points 352
- routine for GPS are 352
- Inverse Menu 357
- Inverse Point to Point 358
- Inverse Point to Multiple 362
- Inverse Point to Location / 363
- Cogo Menu 365
- Point in Direction 366
- Intersection 367
- Corner Angle 372
- Compute Area 373
- Triangle Solutions 374
- Map Check 375
- Add / Edit Line 376
- Add / Edit Curve 376
- Add to Map 377
- Predetermined Area 378
- HD/VD to SD/ZA 380
- SD/ZA to HD/VD 381
- AU Conversion 382
- Curve Menu 383
- Curve Solution 384
- Results: 385
- Known PI and Tangents 386
- Three Point Curve 387
- Compute Radius Point 389
- Line Tangent to Circle 391
- Curve Layout 392
- Tan Dist 393
- Chord Dist 394
- Traverse on Curve 396
- Parabolic Curve 398
- Parabolic Layout 400
- Straight Grade 402
- Spiral Layout 404
- Traverse on Spiral 405
- Roads Menu 407
- Add/Edit Templates 408
- and the slope 409
- Edit Segment 410
- Edit Alignments 411
- Add/Edit Roads 411
- Roadname 412
- The Road Card 413
- Roads Report Screen 413
- Road Profiles Screen 415
- The Templates Card 416
- Add / Edit Template Screen 417
- The Widenings Card 418
- Add / Edit Widening Screen 419
- Super Elevations Card 420
- Road Stakeout 423
- if any 425
- Stake Road – Screen Four 426
- Road Slope Staking 429
- H. Map Card 430
- V. Map Card 430
- Slopes Card 431
- Cut/Fill Hinge Points Cards 431
- Road Station and Offset 432
- screen where 432
- Alignment Card 433
- Cross-Section Card 434
- Shot Data Card 434
- Station Equation 435
- Adjust Menu 437
- Translate 439
- Traverse Adjust 442
- Traverse Adjust – Results 446
- Miscelaneous Screens 447
- Past Results 448
- Create Points Screen 448
- Trimble Slant HR -> HR 449
- Convert Slant HI to HI 449
- Quick Pick Editor 450
- Point List Editor 451
- Map View 452
- Map Display Options 454
- Manage Basemaps 455
- Edit Basemaps 456
- Smart Targets 457
- : when checked, the offset 458
- Disable Touch-Screen 461
- Appendix A 463
- Lambert Zones 464
- ...........151, R-386 467
- .................. 151 468
- ............... 151 468
- .............. R-49 468
- ......121, R-134 468
- .R-306 473
- ....R-303 473
- ........ R-314 474
- 16, R-344 474
- ...... 151, R-385 474
Related products and manuals for Software Spectra-precision Survey Pro v4.5 Ranger Reference Manual
(339 pages)© 2020, manymanuals.com. All rights reserved. | 0.852 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals